Scooter Simplicity
Scooter Simplicity
  • 406
  • 2 139 761
Repair Portable Rechargeable 20W LED Work Light
Found this in "Working"-type LED light in the dumpster, thrown away. The charger was missing. Can't resit trying to fix it.. Can I get this lamp to work again, repair it? Is the LED broken? Battery dead?
A-collection aWork with 3s3p 18650 Li-ion Battery
LED 20 Watt
1600 Lumen
Colour Temperature: 4000 Kelvin
Typical, the forward voltage of an LED is between
1.8 and 3.3 volts. It varies by the color of the LED.
Charger is missing, 8.3 Volt on the internal li-ion battery. (very low and could have damaged the batteries)
20 LEDs in series, say 1.6V times 20 = 32 Volts
But as you see it starts earlier at 25 volts. Testing with two lead batteries in series: (12.7x2=25.4V)
Using my iCharger 1010B+. Lipo charge does not work "Battery check, Low voltage", so I have to use NiMH charge mode to try to get the voltage up. I'm using low constant current to charge it, just to be safe and frequently check if the batteries get hot.
----------- specification of the A-Work LED ------
IP65
For 230VAC and charger 12.6Volt.
Nominal voltage: 11.1 (3s3p)
(3.7V per cell)
Charging voltage 12.6V
Li-ion 18650 6600 mAh, Brand: Wintonic
Переглядів: 194

Відео

Whining Disc brakes, front and rear maintenance, lubrication, easy to do
Переглядів 1463 місяці тому
Baotian BT125T-2 Whining Disc brakes, front and rear maintenance, lubrication, easy to do. Brake squealing is normally worn brake pads, but you can have parts in your brakes that needs lubrication. How to service your disc brakes on a motorcycle / scooter. Remove brake shoes and grease it slightly. Whining brakes noise is annoying! Slow-rolling wheels, time to grease the brakes. Be careful not ...
Baotian BT125T 2 Ep 6 Will it run
Переглядів 1293 місяці тому
BT125T-2 Episode 6, Will it run?! Putting 24mm carburetor Shen Wey back after cleaning it. Put new ignition in it, and hooked up a 12V battery. Had some problems with the 15A fuse blowing. Strange engine noise, is it the starter clutch perhaps. What do you think? Testing GY6 139QMB 50cc Vento CDI on this 125cc scooter. Turns out it works. Time for testrun!
BT125T 2 Episode 5, new inlet manifold new fuel filters replace engine oil
Переглядів 1094 місяці тому
BT125T-2 Episode 5, new inlet manifold, Tong Bu, Clean Drain pipe tank level sensor and new fuel filter in series. Remove foot panel. check size of valve studs, 54mm or 57mm studs. Turns out they are 54mm., And replace engine oil 10W-30 Biltema motor oil (mineral). PCV outlet, Positive Crankcase Ventilation Replace oil drain plug to a stainless steel magnet one. M12x1.5 thread.
BT125T 2 Ep 4 Variator check, service bushings and replace broken brake switch
Переглядів 764 місяці тому
BT125T-2 Ep.4 Variator and broken brake switch Chalice from water inside the cover. Checking status of belt and weights, and also clean it and service the variator bushing etc. Replacing broken brake switch.
BT125T 2 Ep 3 Cleaning fuel tank, replacing instruments bulb, looking at fuel lever meter
Переглядів 475 місяців тому
Part 3 BT125T-2 This Chinese variant is occasionally referred to as "Hockey Mask” 125 GY6 scooter 152QMI Cleaning fuel tank, replacing instruments bulb, looking at fuel lever meter. The Ethanol E5 or E10 fuel condenses and also attracts water from condensation on the inside of the tank Testing for spark. Replacing ignition lock with a new, have to reallocate cables (re-route) Removing exhaust -...
Baotian BT125T 2 Ep 2 Troubleshooting electrical problems
Переглядів 1385 місяців тому
BT125T-2 Ep.2 electric problems Baotian BT125T-2 Episode. 2, check out episode 1 if you’ve missed it! Finding rubber hose in intake valve! Under intake manifold. Also troubleshooting electrical problems, loose connections Switches not working? Starter relay problems? Short circuit somewhere Electric start motor do not work. Brake switch is broken. Test vacuum diaphragm plunger assembly with sta...
Series Baotian 125 Picking up a stuck or seized engine Scooter
Переглядів 1986 місяців тому
Series: Picking up a stuck / seized engine Scooter Baotian BT125T-2 Episode 1 On my way picking up Baotian BT125T-2 whose engine is stuck and seized. The scooter is taken apart and in general poor condition after being outside in rain and debris, probably for years. Previous owners don't know much. He got the scooter with another purchase. The owner tells me he has bought a new battery but won'...
From CVK carburetor PD18J to PZ19 slide Carburetor
Переглядів 3636 місяців тому
From CVK carburetor PD18J to PZ19 Carburetor on Baotian Sprint & Testdrive Testing diffrent main jets and Also replace Throttle Cable) PD18J is of type constant velocity carburetors and uses Vacuum to pull throttle. Slide carburetor or flatslite (I think) is more simple. PZ19 does not have accelerator pump for example. PZ19 is 19mm (widest opening) and I bought the version with Cable Choke. Sim...
ZX Engine Renovation Ep 5 Putting stator, piston and everything back
Переглядів 976 місяців тому
VärmdöScooter: ZX Engine Renovation Ep.5 - Putting stator, piston and everything back Mention stator cables, pick up, exciter coil and what not. Honda MT50 12mm rod pin New piston and new 49cc cylinder from mopeddelar since the old was kaputt. Sound / noise from variator, some kind of play? Music: Kevin Macleod - At Rest No test ride will be made yet, just putting it back after replacing bearin...
Porting and Polishing kit with Pen grip, testing Meec Tool with Dremel Carbide Burr
Переглядів 937 місяців тому
Porting and Polishing kit with Pen grip, testing Meec Tool with Dremel Carbide Burr Here I try out Grinding Engraving mashine from Meec Tools which works good. 170W and adjustable revolutions per minute 8000-3500 rpm. I get no compensation for this so this is my honest tryout. This is what I bought. Kit Includes flex shaft / flexible extension axle meaning pen grip for better access. Accessorie...
VarmdoScooter ZX Engine Renovation Ep 4 new crank bearings and oil seals
Переглядів 647 місяців тому
VarmdoScooter ZX Engine Renovation Ep.4 new crank bearings Putting in new crank bearings and crankshaft and oil seals Short summary. In November 2022 I bought a Kymco ZX from a girl who lived in Saltarö, Värmdö. According to her statement, only the gas wire was faulty. So I thought I'd take the plunge and hit the ground running. However, it turned out to be much more of a problem than the gas w...
VarmdoScooter ZX Engine Renovation Ep 3 Porting Boost Port and intake manifold with Meec Tool
Переглядів 887 місяців тому
VärmdöScooter: ZX Engine Renovation Episode 3 or Part3 Porting Boost Port and intake manifold with Meec Tool Grinding / Engraving Machine 170 Watt 8000-35000 rev per minute Milling with tungsten carbide (If I translate correct). SUNREEK 10 stycken 1/8 tum volframkarbidborr, dubbelskuren roterande borr, 3 mm skaft passar för Dremel
Polini Contessa also know as Polini Sport what's in the package
Переглядів 2197 місяців тому
Can not call a review though, just sort of unboxing. 119.0077 Kit Honda GP-SP-SC01-DIO Kymco CX-DJY Honda Honda Elite 50 Dio Kymco ZX50 Polini Contessa 70cc Cylinder 119.0077 Honda Elite 50 Dio Sym DD50 Kymco ZX50, DJ50 Motori Polini Contessa 47 mm diameter of Cylinder and piston. AF16 AF18 and many more! Contessa is a really good cylinder according to many. Ported is even better but it will ne...
Remove Oil seals on 2 stroke scooter How to not do it
Переглядів 577 місяців тому
Remove Oil seals do not do as I did Remove oil seals very carefully! Do not do as I did.. I got a scratch in the aluminum which might lead to leaks. Might work with silicone gasket tube to fix it. That's how I did. But have not tried it yet. 2 stroke engine from scooter / moped.
Adjust valves on Baotian Comfort GY6 50cc
Переглядів 1438 місяців тому
Adjust valves on Baotian Comfort GY6 50cc
ZX Engine Renovation Ep 2 splitting the case with devor Tool
Переглядів 1308 місяців тому
ZX Engine Renovation Ep 2 splitting the case with devor Tool
How to Remove flywheel on scooter moped and get access to stator
Переглядів 2028 місяців тому
How to Remove flywheel on scooter moped and get access to stator
VarmdoScooter ZX Engine Renovation Ep 1 no compression and test new cylinder
Переглядів 1468 місяців тому
VarmdoScooter ZX Engine Renovation Ep 1 no compression and test new cylinder
Kick start problem med Moas ZX, och jämför skillnader mellan två SC 10 motorer
Переглядів 409 місяців тому
Kick start problem med Moas ZX, och jämför skillnader mellan två SC 10 motorer
Kick start problem on the Moa's ZX, and comparing some diffrences between two SC 10 2 stroke engines
Переглядів 709 місяців тому
Kick start problem on the Moa's ZX, and comparing some diffrences between two SC 10 2 stroke engines
Biltema Impact Wrench Review for scooter repair work
Переглядів 7639 місяців тому
Biltema Impact Wrench Review for scooter repair work
Replacing kick start mechanism on Baotian Comfort Scooter GY6
Переглядів 3529 місяців тому
Replacing kick start mechanism on Baotian Comfort Scooter GY6
A whole video unpacking things bought for the scooters
Переглядів 8310 місяців тому
A whole video unpacking things bought for the scooters
SWEDISH Rostskydd smeta ram och avgasrör med linolja och Biltema asfaltmassa Moped Scooter Kymco ZX
Переглядів 18810 місяців тому
SWEDISH Rostskydd smeta ram och avgasrör med linolja och Biltema asfaltmassa Moped Scooter Kymco ZX
Ep 7 Rust proofing frame and exhaust pipe with linseed oil and Bitumen based anti rust undercarriag
Переглядів 13410 місяців тому
Ep 7 Rust proofing frame and exhaust pipe with linseed oil and Bitumen based anti rust undercarriag
Ep 6 Getting another Kymco, Remove Oilpump and install Oil Delete plug & go Premix
Переглядів 79810 місяців тому
Ep 6 Getting another Kymco, Remove Oilpump and install Oil Delete plug & go Premix
Ep 5 of Getting another Kymco, Remove fuel and oiltank, hose to oilpump & test electronics such as
Переглядів 25610 місяців тому
Ep 5 of Getting another Kymco, Remove fuel and oiltank, hose to oilpump & test electronics such as
Kymco ZX Scooter Ta bort motor från ram (Swedish language)
Переглядів 16410 місяців тому
Kymco ZX Scooter Ta bort motor från ram (Swedish language)
Ep 4 Getting another Kymxo ZX Exploring & Removing engine from frame
Переглядів 13511 місяців тому
Ep 4 Getting another Kymxo ZX Exploring & Removing engine from frame

КОМЕНТАРІ

  • @robertojeda88
    @robertojeda88 2 дні тому

    Hey I have a question. There is two drains for the coolant? One for the engine and the other for the tank?

  • @SmokestackLightning3.14
    @SmokestackLightning3.14 9 днів тому

    Yo man, there was absolutely nothing instructional about this video. Yeah, it cleared without the tire on the rim but is it going to clear with the tire on?? What was the point? You showed the rim was not spinning true, and then suddenly it's spinning true. What did you do and why didn't you show it or at least explain what you did

  • @kadrialfaz2457
    @kadrialfaz2457 10 днів тому

    Nice

  • @julienhagen7411
    @julienhagen7411 22 дні тому

    clean the caburator main nozzel

  • @schwinnvitya4078
    @schwinnvitya4078 23 дні тому

    Hello, if you apply 64 volts to the input, will it ruin it?

  • @MRORIGINALCONCEPTGARAGETEAM
    @MRORIGINALCONCEPTGARAGETEAM 24 дні тому

    Somthing I just noticed is I think the box you didn't know what it was is the actual cdi. Ours is a 2005 model kymco super fever zx50 II and it only has that one box on it. Just an observation brother hopefully it helps.

  • @markitooshernandez6791
    @markitooshernandez6791 28 днів тому

    Weight?

  • @ORIGINALCONCEPTGARAGE
    @ORIGINALCONCEPTGARAGE 29 днів тому

    That be normal for brake levers bends as we though it been dropped because our zx50 super fever II also has its brake levers the same way.

  • @patrickchang-leng1073
    @patrickchang-leng1073 Місяць тому

    Good video but the temperature gauge looks a little high.

  • @sneakyjaguar5982
    @sneakyjaguar5982 Місяць тому

    This is the only video i found about scott voltage mx30. I actually just bought a similar bike. The bike has not been taken cared of but all parts are still intact except grips. I wonder how much did you sell for it?

  • @garagedreams4391
    @garagedreams4391 Місяць тому

    This can also be done in B7 saloon/sedan. It is plenty long. You get in from one of the back doors and slide legs under the back window deck. You want about 4 inch foam in trunk to make it more level. Very stealthy.

  • @cgi2173
    @cgi2173 Місяць тому

    What happens if you use a 6 pin (for the 12v on the PSU) SATA power cable and plug it in to a SATA hard drive?

  • @cableguy6843
    @cableguy6843 Місяць тому

    I’m gunna ask a question,the speedo broke down at the wheel. What’s the little metal connector called that the speedo goes into .that’s where mine broke. I have the new speedo cable but it won’t goin because it’s broke off clean at that connector?

  • @Stoupa1964
    @Stoupa1964 Місяць тому

    Stupid boring video First start to learn how to speak understanding English Then start make the video after you have in your hands the parts Buy yourself a proper lamp Finally know before you start what you need to do when changing the belt I stead of thinking at the moment self that reduces your rhetoric questions

  • @rymamchang8275
    @rymamchang8275 Місяць тому

    Takol ku obeng

  • @killle28
    @killle28 Місяць тому

    tänder på fel ställe........

  • @killle28
    @killle28 Місяць тому

    varför dubbla sopparkranar? å varför försöker du prata engelska när du bor i västerås? 😂😂

  • @cococutie
    @cococutie Місяць тому

    very solid and good stroller

  • @MrMani207
    @MrMani207 Місяць тому

    How to reset A02 alarm?

  • @rynnff4648
    @rynnff4648 2 місяці тому

    One year and no comment!?!? Amma fix that, also this is Very helpful tahnk u so much i fix mine bc of ur video ❤❤

  • @TheyKnowWhoThisIs
    @TheyKnowWhoThisIs 2 місяці тому

    Looks like a worthy cause!

  • @MahoX-rl2oq
    @MahoX-rl2oq 2 місяці тому

    Put a new CDI in it and then hope IT will work

  • @srosh218
    @srosh218 2 місяці тому

    Snyggt! Skulle vara bra om du hade en kamera på huvudet så kan du snabbare och lättare jobba och visa oss! Tack!

  • @jhPremiumDetailer
    @jhPremiumDetailer 2 місяці тому

    Olá bom dia ! Estou com o Rittal sk 3385500 com a falha de A07 qual seria essa falha.

  • @DoktoUr_Youtubecsatorna
    @DoktoUr_Youtubecsatorna 2 місяці тому

    i like this oil! I hope not recycled oil.

    • @gikaradi8793
      @gikaradi8793 2 місяці тому

      Propably it is BUT outside my positive xperience ive heard also good reviews around .Just change it more often

    • @DoktoUr_Youtubecsatorna
      @DoktoUr_Youtubecsatorna 2 місяці тому

      @@gikaradi8793 ok but cant it damage?

    • @gikaradi8793
      @gikaradi8793 2 місяці тому

      @@DoktoUr_UA-camcsatorna most reviews are positive included mine for 100000km in my car BUT there are some mechanics they say theyve repaired engines that used these oils ,Rule of thumb change at every 3-5000km And car and wallet will be ok

    • @DoktoUr_Youtubecsatorna
      @DoktoUr_Youtubecsatorna 2 місяці тому

      @@gikaradi8793 ok thanks :D

  • @CatRadioactive
    @CatRadioactive 2 місяці тому

    Grymt 🔥

  • @nordicaffairs4379
    @nordicaffairs4379 2 місяці тому

    How to tighten or losen skues/bolts?

  • @JP85FIN
    @JP85FIN 2 місяці тому

    Had this bike since 2019 (or 2020), still works like a charm.

    • @airsoftbyed2885
      @airsoftbyed2885 Місяць тому

      Do you know if you Can make it go faster that it does Stock?

  • @20somthingrealestate
    @20somthingrealestate 2 місяці тому

    Holy hell. Wtf are you doing. Yeah of course the bearings are in bad shape after you beat them with a punch

  • @JustRicardoNL
    @JustRicardoNL 3 місяці тому

    Arent you worried to tighten the bolts too much with this thing?

  • @salemhardan6412
    @salemhardan6412 3 місяці тому

    Thank you, im trying to spend as little as possible to be able to continue working with the moped. My Ryobi with 2.4mah battery didn't make the job.

  • @deecee6355
    @deecee6355 3 місяці тому

    Verkar vara en skit produkt tar ju inte bort mycket

  • @tiddybearkush
    @tiddybearkush 3 місяці тому

    Wow im amazed you never understood that you need to use an extension pipe on the wrench to get more leverage to losen tight nutts and bolts ....

  • @asifkashem8861
    @asifkashem8861 3 місяці тому

    Funkade tajt 0,1mm insug och lös 0,1mm avgas bra? Funderar på om det är det rätta mellanrummet.

  • @MangScoots
    @MangScoots 3 місяці тому

    super helpful, i need t replace all of the bushing on my scooter and i didnt know there was this tool. i was gonna drill out the old one and probably end up cracking the case lmao

  • @scooterrehab6295
    @scooterrehab6295 3 місяці тому

    Nice‼️ I just picked up one of those today.

  • @TheyKnowWhoThisIs
    @TheyKnowWhoThisIs 3 місяці тому

    Boatian is an interesting name! Is that a Chineese machine?

  • @elliotkahitamina8252
    @elliotkahitamina8252 4 місяці тому

    Where can i buy this send me the link

  • @Hiranthaperers
    @Hiranthaperers 4 місяці тому

    Can you tell me please how to make Honda CD 125 benly CDI unit

  • @danieljensen9195
    @danieljensen9195 4 місяці тому

    Rad två på id-plåten på fjäderbenstornet ( i hans fall kod 139-2) står det på volvo 240,7-940. Vilket skick det är på hans pärla

  • @Papahaviaris
    @Papahaviaris 4 місяці тому

    I have a 5 pin cdi and my motorbike has 6 pin cpi if i do this up side down it will works

  • @richboy271
    @richboy271 4 місяці тому

    Thank for this video

  • @TheyKnowWhoThisIs
    @TheyKnowWhoThisIs 4 місяці тому

    You Can't beat Free, really...

  • @TheyKnowWhoThisIs
    @TheyKnowWhoThisIs 4 місяці тому

    Great job!

  • @ollekarlsson663
    @ollekarlsson663 5 місяців тому

    Yes it is. You shower in the same space as the WC.

  • @ArjayMartin
    @ArjayMartin 5 місяців тому

    cool. I feel like I've gone on the journey with you now!

  • @ArjayMartin
    @ArjayMartin 5 місяців тому

    Why oil the air filter?

  • @user-tm9dl8sm7f
    @user-tm9dl8sm7f 5 місяців тому

    Can you take a video of which lights and blinkers in the rear should be working when there is all functional please? Thank you

  • @familyinspiration5429
    @familyinspiration5429 5 місяців тому

    What number of the timing belt we need to buy?

  • @electronistul
    @electronistul 6 місяців тому

    Hello, can you confirm that the coulombmeter function does what I think it does, namely: During the life of a battery 1-10 years (whatever it is) it charges and discharges, the coulombmeter function measures what current comes out and what current comes in (subtracts and adds - averages, etc.) then results (normally after several cycles, not instantly) the capacity in Ah of the battery. Let's say we have a 100Ah battery and I cycle it 20-80%, the coulomb meter should show me after some time a capacity of 60Ah (ideal). If we reduce the losses, I think somewhere around 55-59Ah. This is true ? Does it do what I think?